Ornament ring box3/28/2024 Apply glue to the miters and then “fold up” the box, inserting the top and bottom panels into the grooves.Ĭlamping the glue up with a web clamp makes this much easier, but f-clamps work well also. By cutting the sides from the same piece you can achieve a continuous grain flow around the whole box.Īssemble the jewelry box by laying the side pieces end to end in a straight line and taping the joints on the outside. Do some test cuts in scrap before making the grooves to be sure your top and bottom panels fit snugly.Ĭut the sides to length, 5″ and 10″, with miters on each end. They are located 3/16″ from the top and bottom. The grooves are 1/4″ wide and 3/16″ deep. Next, cut the grooves in the sides of the DIY jewelry box for the top and bottom panels. I resawed the pieces on the bandsaw to get two pieces 16″ long and just under 1/2″ then took them to the drum sander and brought them down to 3/8″ in thickness. I cut mine to 16″ long to be split in two next. You’ll need two 10″ piece and two 5″ pieces. Make the Sides of the DIY Wooden Jewelry Boxįor the sides, cut your pieces into 3-1/8″ wide strips. If you aren’t using resawn lumber or glue ups, cut your top panel and bottom panel for your wooden jewelry box to 9-1/2″ by 4-1/2″. It’s easy to get right down to a specific dimension quickly.Īfter they were flat I glued the pieces together into 2 panels and then cut them to size. This is one of the best uses for the drum sander in my book. Next I put them through the 19-38 drum sander to get down to a final dimension of 1/4″. I resawed the walnut into 2 pieces on the bandsaw then cut those in half to finish with 4 pieces. If you are just using a solid one piece panel or 1/4″ plywood this will be very easy. I used a larger piece of walnut with some nice figure to make my tops and bottom panels. Make the Top and Bottom Panels of the Jewelry Boxįirstly you’ll make the top and bottom panels. I used the maple for the sides of the box and walnut for the top, bottom, and lining for a nice contrast. So I cut material for two boxes which you will see some parts for both boxes in the pictures. I had this piece of curly maple with amazing figure I’ve been looking to use. So you can buy nice hardwoods for the box and not break the bank. The best part is this build takes very little wood. I also have jewelry box plans for beginners above so make sure to check those out. You can easily adjust the size to any dimensions you’d like and use these same methods. I like the 2:1 ratio look on the box and this size seems to be just big enough to be substantial, but not too big. Isn’t this a cute makeover project, and you can certainly complete it in only a few hours.I made the wooden jewelry box 10″ x 5″ and 3″ high. This little jewlry box is perfect for my daughters treasures, she has something in every drawer! It even has a music box, that plays a sweet melody! I was a bit concerned about the yellow velvet lining inside, but I think it works with the rest of the colors. Lawless Hardware on hand that suited the makeover perfect! I was honestly worried they would be too big, but they worked great, and the fact they were all mismatched, gave it a unique touch. Luckily I had some sweet glass knobs from D. I would have stuck with the original hardware and just spray painted them, however one handle was missing. I mixed one of my favourite colors ( Voice of Color Wintergreen Mint PPG1229-2) with a bit of BB Frosche Chalk Paint Powder, and within a few minutes, I had updated this drab chest. When paint was the theme for So You Think You’re Crafty last week I decided to dig it out of the ‘needs makeover’ pile and give is a breath of fresh air!Ī little paint went a long way, updating this little 80’s Jewelry box. A while back I came across a very dated jewelry box at the thrift shop, it was only $3.99, so I scooped it up.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |